Leviton Switch ACS15 1L User Manual

Single Pole (One location) or 3-Way (Multi-location)  
Electronic Switch  
Cat. No. ACS15-1L (Lighted)  
Incandescent-1800W – Magnetic Low-Voltage-1800VA (1440W)  
Electronic Low-Voltage-1800W – Fluorescent-1800VA – Supplemental-1/2 HP  
120VAC, 60Hz  
DI-000-ACS15-00A-X0  
INSTALLATION INSTRUCTIONS  
WARNINGS AND CAUTIONS:  
WARNINGS AND CAUTIONS:  
To be installed and/or used in accordance with appropriate electrical codes and regulations.  
Use only one (1) electronic switch in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4  
matching remotes with LEDs.  
Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.  
Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.  
Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.  
If you are unsure about any part of these instructions, consult a qualified electrician.  
Acenti™ electronic switches are not compatible with standard 3-way or 4-way switches. They must be used with  
compatible Acenti™ on/off remotes.  
Recommended minimum wall box depth is 2-1/2".  
* IMPORTANT: For 3-Way applications, note that one of the screw  
Installing your Switch –  
Tools needed to install your Switch:  
Step 5a  
Step 4 contd  
terminals from the old switch being removed will usually be a  
different color (Black) or labeled Common. Tag that wire with  
electrical tape and identify as the common (Line or Load) in both  
the switch wall box and remote wall box.  
Single-Pole Wiring Application:  
Slotted/Phillips Screwdriver  
Pencil  
Electrical Tape  
Cutters  
Pliers  
Ruler  
Leviton recommends to temporarily position the Alignment Plate prior  
to wiring the device. If the wall box wires extend at least 6 inches out  
of the wall box, it is also possible to install the Alignment Plate after  
the device has been wired (refer to Wallplate instruction sheet).  
Terminal  
Screw marked  
White (WH)  
INSTALLING YOUR SWITCH  
Preparing and connecting wires:  
Step 3  
NOTE: Use check boxes  
when Steps are completed.  
The Alignment Plate must be installed with the tab towards the bottom.  
This switch can be wired using side wire terminal  
screws or through backwire openings. Choose  
appropriate wire stripping specifications accordingly.  
1
WH  
BL  
WARNING: TO AVOID FIRE, SHOCK, OR DEATH;  
TURN OFF POWER at circuit breaker or fuse and test  
that power is off before wiring!  
Terminal  
Screw marked  
Black (BL)  
Step 1  
Leviton recommends the following 3 methods to temporarily hold the  
Alignment Plate use of device mounting screw, use of wall box wires,  
or use of electrical tape (refer to the following figures):  
2
3
4
Terminal  
Screw marked  
Yellow/Red  
(YL/RD)  
RD  
YL/RD  
Mounting  
Screw  
Cut  
(if necessary)  
Strip Gage (measure  
bare wire here)  
5/8"  
(1.6 cm)  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
N  
Terminal  
Screw marked  
Red (RD)  
A
P
O
T
Alignment  
Plate  
Terminal Label:  
Alignment Plate Held  
By Mounting Screw  
OFF  
Use Terminal for 3-Way or More Applications Only.  
For Single-Pole Applications, Do Not Remove This  
Label.  
Switch  
Identifying your wiring application (most  
common):  
NOTE: If the wiring in the wall box does not resemble  
Step 2  
Side Wire Connection  
Side wire terminals accept  
#14 AWG solid copper wire only.  
Back Wire (either hole may be used)  
Back wire openings use #14-12 AWG  
solid copper wire only.  
Hot (Black)  
WH  
RD  
BL  
Green  
Ground  
Screw  
any of these configurations, consult a qualified electrician.  
B
YL/RD  
Make sure that the ends of the wires from the wall box are  
straight (cut if necessary).  
Remove insulation from each wire in the wall box as shown.  
Black  
Load  
White  
Line  
120VAC, 60Hz  
TOP  
Alignment Plate  
Held By Wires  
Use Terminal for 3-Way or  
More Applications Only.  
For Single-Pole Applications,  
Do Not Remove This Label.  
2
1
2
1
Installing your Alignment Plate:  
Step 4  
3
4
5
Neutral (White)  
3
4
Important Notice for Installer  
WIRING SWITCH:  
Connect wires per WIRING DIAGRAM as follows:  
Electrical  
Tape  
To achieve proper aesthetic installation of the Acenti products,  
the wall surface surrounding the wall box opening must be  
fairly flat and free of irregularities. The wall box must be level  
and recessed or flush to the wall surface. The Acenti installa-  
tion system allows for adjustments that will correct minor flaws  
that may be present in the installation area.  
C
Green or bare copper wire in wall box to Green terminal screw.  
Line Hot wall box wire to terminal screw marked "BL".  
Load wall box wire to terminal screw marked "RD".  
Line Neutral wall box wire to terminal screw marked WH.  
Switch terminal screw marked "YL/RD" should have Red  
insulation label affixed.  
TOP  
Single-Pole  
3-Way  
Alignment Plate  
Held By Tape  
1. Line (Hot)  
2. Neutral  
3. Ground  
4. Load  
1. Line or Load (See important*  
instruction)  
NOTE: If insulating label is not affixed to terminal screw marked  
"YL/RD", use electrical tape to cover.  
This device must be installed with the AcentiAlignment  
Plate. The Alignment Plate is packaged with the Acenti™  
Wallplate, which is sold separately from this device.  
2. Neutral  
3. Ground  
Proceed to Step 6.  
4. First Traveler note color  
5. Second Traveler note color  
NOTE: For matching remote w/LEDs  
installation, the First Traveler becomes  
Line Hot.  
The Alignment Plate will function properly only if it is mounted  
to a flat wall surface as described above.  
For Single-Pole Application, go to Step 5a.  
For 3-Way Coordinating Remote (no LEDs) Application, go to Step 5b.  
For 3-Way Matching Remote (with LEDs) Application, go to Step 5c.  
 

Land Pride Lawn Mower SF25 Series User Manual
Leica Digital Camera D Lux 2 User Manual
Lexmark Printer Z12 User Manual
Lucent Technologies Server Comcode 108678723 User Manual
Makita Impact Driver 6260D User Manual
Makita Sander GV5000 User Manual
Maverick Ventures Thermometer RF 01 User Manual
McCulloch Lawn Mower 532 43 86 30 User Manual
Melissa Dishwasher 758 007 User Manual
Metz Camcorder 34 AF 3N User Manual